BICSI Outside Plant Designer (OSP) Practice Exam

These questions are part of the practice quiz. Start practicing

• Which of the following geometrical arrangements is allowable for conduits on power and communication poles?
• What is the primary method used to describe easements?
• Which value represents the breaking strength of a Class 7 pole?
• What is the minimum number of openings required for a manhole (MH) up to 12' in depth?
• Which term explains the importance of bonding in OSP design?
• What is the consequence of not following proper separation in grounding systems?
• Which of the following is NOT a component of EMI?
• Which type of fiber optic cable features individual jackets for each tight buffered fiber?
• What is an essential component for keeping poles erect in soft ground when instability is present?
• Load coil designs are utilized to mitigate the effects of capacitance buildup in loop lengths exceeding what distance?
• According to NESC requirements, what is the minimum cover for conduits?
• In the context of design criteria, what does "I" represent?
• What is the minimum pressure requirement for underground installations?
• What height does not interfere with aircraft authorities?
• Which factor is essential for the moment strength of a pole?
• Which trencher is suitable for tight soils, heavy clays, or loose rock at depths up to 5'?
• What is an essential factor to consider when planning a cable installation in easements?
• Which anchor does not depend on soil for holding strength and is ideal for steep angles?
• If the lead to height ratio is 3/4 or greater, what can be used as the head guy for cables?
• Which type of material is both ultraviolet and flame resistant?
• What type of braces should not be used when supporting unguyed corner loads?
• What specification must be determined for cable infrastructure planning?
• When can slack span design be used?
• Which equipment is widely used for multiplier splicing operations?
• What is a characteristic of the most flexible design configuration?
• What is a push brace typically used for?
• What type of cable has one jacket and is typically lower in cost than breakout cable?
• What is the ideal reading for any bonding conductor in amperes for AC and DC?
• How far apart should conduits on poles containing both communications and power risers be terminated?
• Which organization sets the standards and competencies for outside plant design?
• What is the maximum recommended connector loss for optimal performance?
• According to OSP guidelines, the pole line should not exceed what percentage based on stringing tension?
• What is the pole depth formula commonly used in OSP?
• What type of connector is typically used for high-density fiber applications in aerial installations?
• What is the ideal usage for thimble eye bolts during cable installation?
• How is the pole slope calculated when considering installation requirements?
• What type of cable installation allows for the collection of ground strikes from buried cables?
• What type of soil is less effective for most anchor applications?
• What height is noted as "75' or lower" designated in OSP terms?
• To prevent electrolytic corrosion in a corrosion high-risk area, how must the building ground be treated?
• How far should pea gravel in a manhole extend beyond the outer edges?
• When designing OSP infrastructure, which aspect is most critical in ensuring long-term durability?
• What does the subsidiary conduit connect?
• Type C wall has a specific advantage in installation. What is it?
• When considering aerial plant design, which factor is NOT relevant?
• What is the maximum OSP cost variance generally accepted?
• What is the best design choice for OSP when it comes to walls for support structures?
• Which type of coaxial cable is recommended for moderate climates?
• Which of the following is a typical reason for using a vault in a cable installation?
• Baseband cabling is typically used for lengths up to what maximum?
• Where does all the splitting take place in a local convergence for PON?
• Pole grades are based on which criteria?
• Joint use agreements are considered in the planning of which plant design?
• Summing loads converts transverse loads into equivalent loads at what distance from the top of the pole?
• What does a pole grade classification primarily influence in OSP design?
• What is the maximum curvature radius for straight conduit before needing to use manufactured bends?
• Which of the following is NOT recommended to be used in OSP design?
• What is Duct Pic used for in underground installations?
• For a lead to height ratio between 1/2 and 3/4 with 2 or 3 spans, how should the head guy size compare to the suspension strand?
• What is considered an important set of deliverables in OSP design?
• Where should catenary poles not be placed?
• What should be used to prevent a pole from leaning sideways if the load is insufficient for guying?
• In an outdoor plant design, what is the primary concern when routing cables through an easement?
• What stress category does PE 80 belong to?
• What is the primary function of the main conduit?
• What is the recommended maximum value for bonding resistance in OSP applications?
• In fiber optic installation, what is the role of individual jackets in breakout cables?
• What is the average lifespan of cables when installed underground?
• A main conduit should enter the _____ of a manhole.
• A structure in height that doesn't exceed what value when crossing in front appears to not interfere with antennas?
• What device provides stability for a pole and keeps it from sinking into the ground?
• Loading capabilities of poles refer to?
• What does moment strength represent in the context of loading?
• Which type of cable is suitable for direct burial applications?
• What type of trencher is best utilized in soft loamy soils or loose clay soils for depths up to 5'?
• What is the purpose of a concrete anchor?
• For optimal performance, what is the preferred loss specification for connectors in fiber optic systems?
• Which equipment is suitable for use in situations where traditional methods of excavation are impractical?
• Which connector is known for being pull and wiggle proof, low loss, and has a small form factor design?
• Which type of equipment is typically used for installation in residential areas?
• What is the preferred size for ground rods used in manholes (MH)?
• If the lead to height ratio is between 1/2 and 3/4 with only 2 or 3 spans, the head guy should be_____ than the suspension strand.
• Which of the following factors is NOT relevant when designing OSP according to safety standards?
• What does subtracting the passive cable system attenuation from the link loss budget provide?
• In OSP, which pole heights are most commonly used?
• Which of the following is a CSI grouping number for telecommunications?
• What is the concept associated with the bonding and grounding noted in NEC Chapter 770?
• Which part of OSP design focuses on electrical safety and security?
• What is the standard spacing for ground attachments under normal OSP conditions?
• In the context of bonding resistance, what does a value of 0.1 Ohms indicate?
• What type of anchor is typically used in hardpan or crumbly damp soil?
• What type of maintenance hole contains an end wall entrance only?
• What is the assumed load considered for heavy applications per meter?
• Which sizing is used for a 5/8" guy rod?
• What is the advantage of planning OSP installations to last for 10 or more years?
• When designing an OSP installation, what factors influence the choice of materials used?
• What is the typical application for an expansion anchor?
• What type of anchor is suitable for use at locations where the anchor rod is permanently frozen?
• To maintain safety, what should the guy height ratio avoid exceeding?
• The support structure that prevents poles from leaning sideways in unstable soils is called what?
• How many townships are found in a range?
• What is necessary to ensure stability in cable installations in windy areas?
• What determines the maximum permissible end to end system attenuation in a given fiber link?
• Which colors are not utilized after the first 24 binders in a fiber optic cable?
• How far below the top of the casing should the bottom of the ditch be at minimum?
• What is the minimum expected lifespan for direct buried cables?
• Which factor is NOT typically considered in pole classifications?
• What is the average lifespan of direct buried and aerial cables?
• Which type of conduit is not suitable for forming shallow curves?
• What principle does a MH/HH intrusion detection system rely on to detect fiber bending?
• What is a characteristic of Type E conduit?
• What stress level is indicated by PE 40?
• Which type of cable ensures optimal system performance?
• What is the typical distance at which direct buried cables collect ground strikes, determined by soil resistance?
• For poles that have communications and power vertical risers, what is the minimum angle that the conduits should be terminated apart?
• What is the recommended minimum cover when high soil compaction cannot be maintained?
• How is the US rectangular grid measured?
• What is the primary role of subsidiary conduits?
• Which item is essential to maintain correct alignment of a pole?
• At what height is an OSP zone defined as 75' or higher?
• When does the need arise for side guys in pole installations?
• What is the economical choice to install when an existing pole is ground braced at both the top and bottom?
• Where is the only location splicing of connector tips can be conducted?
• What is the range of pairs for PE-39 cabling?
• What is used when soil is unstable and there isn't enough space for side guys?
• How many NAP groupings are commonly recognized in OSP design?
• Which factor primarily affects the reliability of a telecommunication system?
• What's essential for ensuring standards compliance in an OSP project?
• What does minimal system loss depend on?
• What is the required resistance to ground for an effective ground using an 8' ground rod?
• What does branch conduit extend from?
• What maintenance holes contain both end and sidewall entrances?
• PE 63 is categorized as which stress level?
• What does Type B wall require for installation?
• What does Pole Grade C signify in terms of line length?
• What size is specified for a 1-1/4" guy rod?
• What is the maximum diameter that an earth boring machine can excavate holes?
• What is the benefit of using water jet hydro vacs for excavation?
• What type of bolt is used when the lead to height ratio is 1-1/4 or less?
• In the context of conduit systems, what does "thick wall" refer to?
• What could be used to repair a bent fiber optic cable?
• What size is used for a 3/4" guy rod?
• Bonding the shield to the _____ will reduce noise level in the telecommunications cable.
• What is the maximum value for a 2-point bonding in central offices expressed in Ohms?
• What formula is used to calculate bending moments in pole design?
• In an MGN power system, what is the position of the neutral conductor relative to the primary conductor?
• What is the minimum percentage that the inside diameter of a casing must be larger than the outside diameter of the largest conduit?
• Which attachment is used at an in-line pole for guying?
• What is the key advantage of using metes and bounds over other land description methods?
• What is the function of head guys in pole reinforcement?
• What is the standard diameter of bolts typically used in OSP applications?
• In pole mechanics, what does T represent when calculating bending moments due to unbalanced tension in the line?
• Which of the following is the highest pole grade?
• In OSP design, what does "C" indicate?
• Which polymer used in insulation is more resistant to electrical surges compared to PE-39?
• When the lead to height ratio is 1-1/4 or greater, which bolt should be used?
• What is the maximum number of cable pairs recommended to effectively use slack span design?
• When selecting support strands for an OSP project, which factors must be considered?
• When must high soil compaction of 85% or greater be maintained?
• What is the service drop load per meter for medium and heavy loading?
• Which type of trencher is optimized for conditions with loose soils?
• What defines a tract of land using lines, distances, and bearings?
• What type of trencher is designed for hardened clay rock soil or adverse conditions?
• What is the transverse load formula?
• Which of the following is a medium assumed load rank per meter?
• What is the maximum number of pairs that PE-89 can handle?
• What is an effective strategy to prevent sagging in cable runs between poles?
• What is the purpose of the maintenance hole type "T"?
• What role do side guys play in cable installation?
• What are the four parts of security in OSP design?
• In which environment would you typically use a screw anchor?
• Which answer best describes branch conduit?
• What does a pole grade of B signify in terms of performance?
• What is an advantage of using fabric mesh innerduct in installations?
• What is an acceptable practice for mitigating EMI in cable installations?
• Typically, grow factor projections are what percentage?
• What is the term for a pole that is not positioned vertically to ensure alignment at the top?
• What role does the "E" factor play in electrical specifications?
• Pole classifications consider which of the following factors?
• When considering coaxial cable, which two major factors must be evaluated?
• How is the separation of electrical and telecommunications grounding achieved?
• What is the definition of "high stress" in the context of conduit types?
• What is the significance of pole grade N in OSP design?
• For how many years should OSP plan design and insulation to accommodate future service growth?
• What type of splicing module is preferred for free breathing space in aerial applications?
• What type of wall may be directly buried with selected backfill for straight runs?
• What can be inferred about a bonding resistance greater than 0.1 Ohms?
• If the pull on a corner pole is 50' or less, how should a guy be positioned?
• Which installation requires one guy on each side for support?
• What do performance requirements describe in relation to telecommunications systems?
• Which installation method prioritizes minimal impact on the surrounding environment?
• Which pole grade represents the lowest grade with no load?
• If the pull is greater than a 45-degree angle, how many dead guys are required?
• What component is used to secure cables at corners?
• Which type of poles should be avoided as storm guying points?
• Which UL standard states that fast response secondary protectors should be installed in a series?
• Which chapter of the NEC covers communications?